KFSSI WIKI

This page is under construction!

Welcome to the KFSSI WIKI pages.

Please navigate to the language you like to use:
Deutsche Version KFSSI WIKI Deutsch
Versión Española KFSSI WIKI Espanol

Introduction

Here is a collection of information and basic methods to coat copper, to produce GANS and to apply all this.

Coating of copper

Nano-wires under the scanning electron microscope after the fire coating, Source: Yuan et al. (2011, p.2492

Fire coated copper under the scanning electron microscope (a) The Cu2O layer and the CuO layer is to see clearly and also the subsequent resulting nano-wires, (b) enlargement of the green marked area of ​​(a) Source: Yuan et al. (2011, p.2493)

Single nano-wire(NW): (a) taken with a transmission electron microscope (BF-TEM), visible are both sides of the nanowire, (b) the high-resolution transmission electron microscopy (HRTEM) shows enlarged the two layers and the crystalline structure, (c) SAED (selected area electron diffraction): pattern of a nanowire, source: Yuan et al. (2011, p.2494)

The base material for the coating is copper, in any form. The coating is carried out either thermally by heating (gas burner) or chemically by etching (NaOH). During the coating "gaps between the atoms" arise and on the surface of the copper microscopic layers build up, which in turn consist of small particles that look like wires, these are also called "nano-wire" because they are so small. Therefore, the coating is often referred to as nano-coating. These nanolayers have the ability to grow during the process of the coating.

Many institutions and universities were already engaged in dealing with the thermal coating of copper. Depending on the nature of the copper at a certain temperature there appear different patterns at the surface called “graphs” or others which are called "nano-wires". For example, the scientists Yuan, Wang, Mema & Zhou (2011) from the Department of Mechanical Engineering & Multidisciplinary, State University of New York have studied these nano-particles and layers in detail. The diagram shows an image of the nano-wires in the size from micrometers or nanometers (1 nanometer is 1 millionth of a millimeter: 1 / 1,000,000). The individual wires (threads) are to see clearly, standing or lying around more or less disordered. In this case the copper has been heated to 450 ° C again and again, over a period of 2 hours. It was used a copper substrate in 99.99% purity, which previously was treated with hydrochloric acid (HCI) and was washed with demineralized water, to clean the copper and to remove the natural oxide layer.

The authors affirm that the "nano-wires" during the heating process do not result out of the the so-called "grain boundaries", the cracks on the surface, but that these evolve independently. In detail, during the coating process on the surface first the copper (I) oxide layer (Cu 2 O) is formed, then a copper (II) oxide layer (CuO) comes into existence and eventually the "nano-wires" grow on the top, out of the CuO layer. Only when the CuO nano-layer is thicker than 1 micron (1 micrometer), the nano-wires begin to grow. The optimum temperature for the growth of the nano-wires is indicated with 300-550 ° C. Interestingly, as we know from the coating practice: copper (I) oxide is yellowish to reddish-brown and gets black when heated, but when it cools down it takes on its original color again. Therefore, if the coated wires are just yellowish to reddish-brown, the CuO layer was not yet formed and consequently no "nano-wires" are created. Copper (II) oxide is black, so it is important that the coated wires are black and do not have the Cu2O colors. It is therefore important to choose the right temperature for the fire coating, which we will describe in more detail at the topic of fire coating.

Furthermore, Yuan et al. (2011) have found that the surface of the nano-wires has a crystalline structure and is not hollow, each side of a nano-wire is a crystal with a clearly specified crystal lattice. In figure a and b the two sides can be seen, shown by transmission electron microscopy.

Steam-coating with NaOH

In order to coat copper wires or plates, you need:

• Plastic container with lid (not too big)
• Weights for weighing down the lid
• ready-wound copper coil, wires or plates
• ~ 100 grams of pure NaOH powder or beads (no drain cleaners; you can buy it in color shops because it is used to remove paint as alkaline-based stripper)
• ~ 2 liters of distilled water (according to the quantity of coils and size of the plastic container)
• electric kettle (water boiler) or oven to heat the water

• 

  Sodium hydroxide in small beads or flakes (cost: approximately 10 euros / kg)

• 

  Distilled water

• 

  Plastibehälter with lid and weight.

• 

  "Raw" copper coils.

Phase 1: NaOH-bath - cleaning the coils (~ 1 day)

Preparation for Steam-Coating

At this stage it comes to cleaning the coils of fat and other substances. In a plastic container (not too big) NaOH powder is easily scattered to cover the bottom of the container, then the prepared copper coils are placed on top of the powder, they can touch each other. Next, the lid of the plastic container is obliquely placed on the container so that only a small inlet remains open. In this intake now boiling water is poured until the water covers all the coils. Caution, steam escapes, please wear protective glasses and protective gloves. Burden the lid with weights, so that not too much steam escapes, and leave the container in this state for 24 hours.

Phase 2: Steam Coating - first coating of coil (~ 2 days)

In a plastic container of the same size as in Phase 1 (it could also be the same container) a zinc grid is put at the bottom of the container, so that the coils are not directly on the plastic. Then wires are stretched on top of the container. The bottom of the container has to be covered with scattered NaOH (less than phase 1). Hang the coils, which were previously submerged in NaOH water, on the wires. The coils should have about 2 cm distance from the ground and should neither touch the container walls, nor the other coils. Next, the lid of the plastic container is obliquely placed on the container so that only a small inlet remains open. In this inlet again boiling water will be poured, but this time only about 1 cm. Close the lid as soon as possible, burden the lid with weights and wait for about 2 days. Use as in phase 1 protective glasses and protective gloves.

Phase 3: polarization of the coil (~ 1 minute / coil)

Polarization of a coil with a multimeter, set to Ohms

By polarizing the layers on the copper surface (coating) get excited to organize themselves, align and stabilize. Proceed as follows:

• Place the still wet coils on a nonconductive surface (wood, plastic, fabric, etc.)
• Measure with a multimeter, set on Ohms, at both ends of the coil the resistance. The coil resistance will be definitely higher than 100 kilo Ohm, usually it is in the range of Mega Ohm.
• After the operation, hang the coils back into the plastic container.

Phase 4: drying (~ 3 days) and "pull potential" (~ every 3-6 hours)

With "pull potential” the process is named where "plasma" by the power of the multimeter is encouraged to move, or to organize. In this process current is withdrawn to stimulate the system to produce new current. Proceed as follows: • Pour the bulk of the liquid from phase 2 out of the container, the coils then start with the drying process. • Remove the coil from the hanger, place them on an iron plate • Touch with the negative pole of a multimeter (set to Volt) the iron plate and then touch with the positive pole only briefly for a few seconds different points (beginning, middle and end) of the coated coils. The measured values ​​have no meaning and vary between + and - on the display of the multimeter.

Repeat this process every 3-6 hours during the three days drying period.

• 

  Potential measurement point 1

• 

  Potential measurement point 2

• 

  Potential measurement point 3

• 

  Potential measurement point 4

Fire coating with gas burners

Gas burner (gas torch, blow torch) with butane gas

With this type of coating it seems to be not necessary to go through the process of polarization and drying (+ pulling potential), but the temperature and direction of the fire coating is crucial. The movement during the fire coating must always be in the direction of flow and the wires must never glow completely. Once the wires get a golden shimmer, the gas burner should be moved further.

If the wires after a few seconds of cooling down take on different colors as red, turquoise or blue throughout an area, the temperature was too low. In this case simply coat again about this passage. If the wire starts to glow, the temperature is too high, in this case simply move back the gas burner a bit (higher distance from the coil) and then start again with the coating. Over time, a sense for the fire coating will develope and everything runs automatically.

We need:

• Gas burner with butane gas (it also works with a propane / butane mixture)*
• Copper coils or plates
• Refractory mounting device for mounting /hanging) the coils or plates (preferably metallic)

Important: Do not coat in too cold rooms, otherwise very easily the coating layer separates from the copper wire; there are also differences in quality of the copper wires, sometimes slight cracks at the surface can be seen already in the "raw" state.

Please be aware to use a gas burner with a tight and narrow flame to be able to apply it very accurate (at the point), as you can see in the Video. If you use a burner which has only a wide, broad flame you will heat up the neighbouring areas too. This disturbs the needed direction of heating of each coil!

https://www.youtube.com/watch?v=gRaeT-7zIJs Video about right method of fire coating

GANS production and application

Formation of GANS. Source: Keshe Foundation SSI, 2015

GANS is the abbreviation for "GAs in Nano-state of Solid". The Keshe Foundation has developed a method by which carbon dioxide (CO2) can be extracted from the air by simple means and converted into a solid state in the nanometer range (nano-state of solid). In the production of CO2-GANS the carbon of the air joins with the oxygen within the salt solution and within a kind of plasma bubble (consisting of Magnetical and gravitational fields) this conjunction is brought in a crystalline form. These crystals absorb the light (the fields), store and release them according to the "demand". Each crystal is like a sun!

Furthermore the Keshe Foundation discovered that this GANS, dried as well as bound in water, is useful as an energy supplier or can be usefully applied in areas of health and agriculture. The GANS-water (= the clear water above the GANS, after all of the GANS has settled, but only after the GANS was “washed” at least 5 to 10 times with distilled water – see description of GANS washing) can be used in various ways. It is possible to pour it into the bathwater, to make patches as wound dressings or to use it as a spray. Small volumes of it like some drops of it diluted in water (Liquid Plasma – see there) you can drink. The applications are almost limitless and yet only rudimentary explored.

The process of GANS-production, developed by the Keshe Foundation, does not only work for the production of CO2-GANS, but also for other kinds of "GANS". The figure shows schematically the development of GANS. The used base is "raw" copper. You can see the indicated compact atomic structure at the bottom of the graphics. In the first step the copper is nanocoated. By the coating the aforementioned gaps between the atoms are formed and nanolayers with nanowires (see Coating) come into existence. This coated copper produced in interaction with a zinc plate in salt water the CO2-GANS, which settles at the bottom.

GANS is required for the operation of the Keshe-Magravs. On the one hand the wound and coated coils are covered with GANS and on the other hand there are GANS-tanks (e.g. ping-pong ball) in the center of the coils. And GANS is required in order to produce GANS-water and this is used to produce GANS fields. These GANS-waters are used in many areas of the society. We describe here only the production of the four basic kinds of GANS, which are produced by immersion of coated copper wires or coated copper plates and various metals in 10% sea salt water (100 Gramm sea salt in 1 liter of distilled water dissolved). Thus, you need for the GANS production:

• Plastic container
• Distilled water
• unrefined, natural sea or rock salt
• coated copper wires for short-circuiting of the metals
• coated copper (plates or coils)
• metal plate uncoated, which is needed for the respective GANS production (zinc, copper, iron)

• 

  Distilled water

• 

  Sea salt, unrefined, or

• 

  Mountain halite (rock salt was once sea salt)

• 

  Plastic tray with lid

Folgende Tabelle gibt einen Überblick über die Entstehung von unterschiedlichen GaNS-Arten unter Verwendung unterschiedlicher Materialien:

GANS	Color	Coated Material	Uncoated Material	salt content
Co2 (ZnO + Co2)	white	coated copper	zinc	3-10%
CH3 (FeO + CH3)	reddish brown	coated copper	iron	3-10%
CuO (CuO + Cu)	turquoise	coated copper	copper	3-10%
ZnO	white	coated copper	zinc	3-10%

CO2-GaNS

Washed CO2-GANS with green LED, generates far less and shows structure. Yield after 4 days.

File:Co2-gans.jpg

CO2-GANS without LED, high amount of Zinc oxide. Yield after 1 day.

CO2-GANS dried without LED, high amount of Zinc oxide. You bring this with the double amount of NaOH (weight) and hot destilled water into a “nano state”. Wash it at least 5 times or more (pour out the water after the GANS has settled and fill the container again with fresh destilled water each time). What remains is pure CO2-GANS (usually very little).

Connections of LED, but please use a green LED!

LED lights when production is going well and electricity is produced!

Production

This GANS is produced by dipping of zinc plates and coated copper coils or coated copper plates in saltwater. Solve 100 grams of sea salt in a liter of distilled water carefully and pour the solution into the container. Ensure that no residues of not dissolved salt come into the container. Regarding the connection of the plates or coils, there are different variants, which lead to a different CO2-/ zinc content.

CO2-/ zinc mixture in the ratio 20/80

In this case the coated copper plate / coil is directly connected to the bare zinc plate with a coated copper wire. The preparation of this mixture works very quickly, the amount of CO2-is however relatively low in respect to the zinc content.

CO2-/ zinc mixture in the ratio 90/10

In this case the two plates (nanocoated copper plate and bare zinc plate) are not directly connected with the coated copper wire, but in the middle there is a LED or the coil of a PC fan mounted. The bottom of the plates or coils should not touch the bottom of the container. Connect the anode (longer piece of wire = positive pole) of the LED with the coated plate / coil, and the cathode (notch or shorter needle on LED package = negative pole) with the zinc plate. After a few hours a white layer starts to settle on the bottom of the container, the CO2-GANS, This means: Use NO CURRENT (neither from batteries nor of power supplies) in CO2-GANS-production!!

We need:

• plastic tub/container or cut bottle
• zinc plate
• coated copper coil
• Green LED
• 100Gramm sea salt
• 1l of distilled water

• 

  Put the rock salt blocks in a 10 liter bucket and fill in the distilled water; wait until salt dissolves (about 1 day) and then filter out the brine. So you can produce brine (salt solution) to stock it and you will always have fresh 15% salt solution.

• 

  Clean the empty bottles and hang them in a prepared board. Please do not clean with chemicals (detergents). Hot water is enough!

• 

  Zinc plates (from a tinner/tinsmith); with a magnet you can distinguish pure metals, as zinc, copper, brass, .... no magnet will stick on them.

• 

  You should get into the habit to bend back all "ends" of ALL wires (make a loop) so that the energy flows back into the metal.

• 

  CO2-GANS production = zinc plate and NaOH coated copper coil (in this case not connected in series)

• 

  Connect the metal with a green LED. In this case, alligator clips (Red & Black) soldered to the poles of the LED for the poles of the LED not being damaged

• 

  Optionally: Addition of oxygen stimulates the production.

• 

  CO2-GANS connected in series with a green LED.

• 

  CO2-GANS connected in series with a green LED.

Effectiveness, application

The CO2-GANS-water (depending on the application either pure or only some drops of it put into a larger volume of water) activates cells, revitalizes the body, bringing the sunlight in the body and strengthens the immune system. As a spray it immediately relieves the pain. In disasters, there are usually broken bones. Do not apply the CO2-GANS-water directly to fractures because the pain at the point of the bone fracture brings in the calcium that is needed for healing. So do not spray directly on the breaking point, but around of it. For all kinds of muscle injuries you need CO2-GANS-water.

• CO2-GANS-water can be taken in (swallowed) Eg. dropwise or 5ml to 25ml in half a liter of water - 1 to 2 times daily (according to the recommendations).
• Foot-bath: add CO2-GANS-water to lukewarm water, repeatedly applied this eliminates athlete's foot, pulls out of the body stored plasma energy of heavy metals.
• Full-bath: here you can not only apply CO2-GANS-water but also the GANS-water of ZnO / zinc, CH3 / iron and CuO / copper. For example, at Radioactive contamination Mr. Keshe recommends to take a bath with 2-3 liters of CO2-GANS-water in the bathtub with warm water and staying in this water for 2 to 3 times a day for half an hour.
• Scalp and hair: you can regularly rub with the CO2-liquid plasma scalp and hair. - It soothes the scalp, strengthens the hair root, and is supposed to bring the original hair color back.
• CO2-+ ZnO liquid plasma mixture to spray on the face: revitalizes the skin, refreshes, rejuvenates the skin.
• As aftershave lotion: alleviates possible cuts immediately and relaxes the skin.
• eczema: spray the affected skin areas with the CO2-GANS-water - very rapid improvement has been reported.
• Bee sting: sprinkle with CO2-GANS-water several times

CO2-GANS, CO2-GANS-water and the liquid plasma of CO2- is not only used in health applications but also for energy production.

CH3-GaNS

Schematic setting of CH3-production without current; instead of the shortcut you can also use DC of a battery

Production

This type of GANS is produced by using an iron plate and a coated copper coil dipped in sea water (or a solution of sea salt). The two metals are connected by a copper wire. Unlike the production of CO2-GANS you can use here a very low/small amount of DC current and the air of a fishtank pump to speed up the process (but this is not really necessary). Members of the Keshe foundation use i.a. a common, adjustable DC device, which produces current of approximately 15 mA between the two plates (metals), instead of the connection with a copper wire. In this case the minus pole of the device is attached to the coated metal (coated copper) and the plus pole of the device is connected to the blank, not coated iron plate. You could also use a 1,5 V battery as power source. If you use any kind of current you should in addition definitely feed air into the salt solution e.g. with a fish tank pump. After a few hours the production of a reddish brown layer at the bottom of the container starts. This is the CH3-GANS. To get a better result, as described with the CO2-GANS production, you can mount a coil of a PC-fan between the two metals (instead of a wire or a current source). We need:

• Plastic Container
• Iron plate
• Coated copper coil (or coated copper plate)
• 100 gram sea salt
• 1 liter distilled water
• Optional: DC-Device and fishtank pump

• 

  Iron plate, coated copper coil, oxygen pumped in and 0,15 Amp current (battery)

• 

  Washed CH3 GANS

Effectiveness, application

CH3-GANS-water und Liquid plasma of CH3-GANS act strong energizing upon the body. It is also a part of the nutrition: for instance, 8 parts (drops) of GANS-water of CH3, 1 part (drop) of ZnO, 1 part (drop) of CO2. The fields of Ch3-GANS-water give the energy, those of ZnO are supporting the nervous system and those of CO2 act connecting the muscles with the nervous system. The carbon within CH3 and CO2 releases energy and the hydrogen of CH3 and the oxygen of CO2 join and provide the moisture, which is needed within the body. The energy of the H of CH3 becomes food. The ZnO/Zinc oxide supports the nerve connections which are needed to implement this energy into the body. Always add one drop of the respective amino acid (which builds on top of the salt water during the process of GANS production in each of the containers), this assures that the application is able to be effective within the body. Everytime when you want to apply CH3 as food you must add amino acids. The amino acids tell the body that the energy is provided for the body. The GANS and the amino acids are created within the same container and therefore have an inner connection regarding their inner structure. This inner connection is obviously necessary for the fields of the GANS and its information, which are available within the GANS-water and the liquid plasma, to be transferred to the molecules of the cells of a living body. The real procedures are topic of present and future research.

CH3-GANS is also necessary for technical energy production.

CuO-GANS

CuO-GANS before it has settled. CuO-GANS has just to settle.

Production

For the production of CuO-GANS you need a blank copper coil (or copper plate) and a coated copper coil (or a coated copper plate), dipped in a sea salt solution. The two metals (plates or coils) get connected by a copper wire. To speed up the process, the same as with the GANS production of CH3, you can use here a low/small amount of DC current and the air provided by a fish tank pump. Some members of the Keshe Foundation use a DC-device which provides approximately 15 mA DC current between the two plates (or coils) instead of the copper wire. The minus pole of the device is to connect with the coated copper and the plus pole of the device is to connect with the blank copper. If you use current then you have in addition also to apply a fish tank pump to provide additional oxygen. After a few hours a turquoise layer builds on the bottom of the container and settles there. This is CuO-GANS. To get a better result, as described with the CO2-GANS and CH3-GANS production, you can mount a coil of a PC-fan between the two metals (instead of a wire or a current source). We need:

• Plastic Container
• Blank copper plate (or coil)
• Coated copper coil (or coated copper plate)
• 100 gram sea salt
• 1 liter distilled water
• Optional: DC-Device and fishtank pump

Effectiveness, application

Copper represents (in connection with the field interactions) the physical body, it effects the muscle tissue and the nervous system. Copper is responsible for a good communication through the nerves and copper acts disinfectant. In Ghana the Keshe Foundation in cooperation with the national Atomic research institute carried out tests, where microbial contaminated drinking water was cleaned with CO2- and CuO-GANS-water so that is was transferred into drinkable water. Bacteria, salts and even Arsenic and Mercury could be neutralized through CuO-GANS-water so that it was no more detectable in the tests. With the GANS-water of CuO many areas can be disinfected. e.g. rooms where food is produced, hospitals, kitchens, toilets, bathrooms and so on. CuO is also used in the technical energy production.

ZnO-GANS

ZnO-GANS.

Production

For the production of ZnO-GANS you need a blank zinc plate (or zinc coil or zinc mesh) and a coated zinc coil (or a coated zinc plate), dipped in a sea salt solution. The two metals (plates or coils) get connected by a copper wire. To speed up the process, the same as with the GANS production of CH3, you can use here a low/small amount of DC current and the air provided by a fish tank pump. Some members of the Keshe Foundation use a DC-device which provides approximately 15 mA DC current between the two plates (or coils) instead of the copper wire. The minus pole of the device is to connect with the coated copper and the plus pole of the device is to connect with the blank copper. If you use current then you have in addition also to apply a fish tank pump to provide additional oxygen. After a few hours a white layer builds on the bottom of the container and settles there. This is ZnO-GANS. To get a better result, as described with the CO2-GANS and CH3-GANS production, you can mount a coil of a PC-fan between the two metals (instead of a wire or a current source).

We need:

• Plastic Container
• Blank zinc plate (or coil)
• Coated zinc coil (or coated zinc plate)
• 100 gram sea salt
• 1 liter distilled water
• Optional: DC-Device and fishtank pump

Effectiveness, application

The field strength of ZnO/ Zinc plasma is able to interact with the field strength of emotions. Therefore it addresses our emotions. It supports, strengthens, balances, fills and pacifies emotional needs. The plasma of ZnO/ zinc is the “peace plasma”. Zinc plays an important role in the wound healing. Zinc is a key component in more than 80 metabolic cycles.

• In health applications the GANS-water or liquid plasma of ZnO can be applied everywhere where the GANS-water of liquid plasma of CO2 is used, because emotional imbalance, conflicts, stress and so on are the most frequent causes of illness and diseases. Therefore ZnO plasma is able to support almost all healing processes.

• Health cup with double walls: The gap between the walls of the cup is filled with GANS-water of ZnO/ zinc oxide. You do NOT fill water into the cup, but you breathe in only the air inside the cup with a straw.

Useful conditions of GANS

GANS is needed in various conditions. The less water is within the GANS the more solid the substance gets, till you reach the condition of a powder. Before you get there some steps are necessary:

Harvesting the “amino acids”

Before you are able to deal with the GANS you have to pick up the oily substance which is created during the GANS production and is floating on top of the salt water, because this substance is a valuable ingredient for a lot of applications. This oily layer obviously is a kind of organic substance. Mr. Keshe speaks about “amino acids”. What actually is created in each of the GANS containers, and which variation under which circumstances and conditions, has to be investigated in due course of time. For simplicity reasons and provisional these substances, which are created on top of the salt water of the GANS production container, are called “amino acids”, because amino acids are essential parts of the physical body of a living being.

These layers of amino acids, which are swimming on top of the salt water, are quite thin. Therefore it is not so easy to collect them. You can suck them in with a pipette or a syringe (but in this case you will collect much of the salt water too). It is better to take a tool (e.g. a spoon, a glass rod,…) and touch them with this tool so that they will be attached to it. You can also use a sheet of paperboard or a plastic foil to pick up this layer on top of the salt water. You will have some training to do it well.

The harvested amino acids you can store in liquid form, or, especially if you collect them with a paperboard, you can dry it in a sunny place. Then you can fill the powder in a glass or can. Please always label it instantaneously (e.g. with: amino acids above CO2-GANS)

As soon as you have collected the complete layer of this oily substance (amino acids) – probably in a few attempts – you can start with the process of washing the GANS.

Washing of the GANS

To get usable GANS the GANS has to be washed to reduce the salt content. This happens in the following steps:

• Pour out or suck in the salt water above the newly created GANS carefully with a syringe or manual pump**
• Put the liquid with the GANS flakes in a preferably high glass jar (or another high container)
• Fill this glass jar with the GANS flakes with distilled water up to the top
• Wait till the GANS flakes have settled at the bottom of the glass jar
• Suck in the water above the settled GANS with a syringe or a pump again
• Fill again distilled water into the glass jar with the settled GANS flakes

Repeat this process (sucking in the water above the GANS and filling up with new distilled water) at least 6-10 times, after this the GANS is washed.

• • Alternatively: If you have produced your GANS in bottles, mounted in a board upside down, you can open the srew cap of the bottle and let the GANS carefully pour out.

Additionally to the methods of GANS production, which were introduced here, there are a lot of alternatives. In due course of time they will be introduced too.

Production of GANS-Water

GANS-water filled in bottles

Drying of the GANS on top of the heating

As soon as the GANS is washed several times there is hardly any salt in the suspension. Then it can be used for further processing.

To get GANS-water you have to fill up the glass jar with the GANS flakes with distilled water again after the last washing run. Stir the suspension very well to strengthen the field transfer and the transfer of information.

For the water to be able to absorb the fields and the information which are released by the GANS completely, you should leave the suspension for at least 24 hours.

Afterwards the water above of the already settled GANS can be considered as charged with the field properties of the GANS and as informed. Now it can be used for the various applications. This newly charged/informed water above the settled GANS is called “GANS-water”.

If you take from this GANS-water for your applications please be aware to suck in actually only the clear water and nothing of the GANS flakes themselves (except you need them consciously and deliberately).

The GANS itself (the GANS-flakes) stays in the glass jar (or other container) and can be filled up with new distilled water again and again, limitless.

After you fill it up again please stir it well and leave it for at least 24 hours. Now you have produced a new charge of GANS-water.

Production of “Liquid Plasma”

From every type of GANS-water we can produce the respective “liquid plasma”. For the production of “liquid plasma” you take a few drops or ml of GANS-water with a pipette or a syringe and “vaccinate” these few drops of GANs-water into another container of fresh pure distilled water.

The information is transferred from these drops to the whole water content of this container instantaneously, especially if it is stirred or shaken properly. For stirring you use preferably a stirrer which you easily can produce by yourself with a nanocoated copper coil and a rod. The turbulences due to the created vortexes within the water act like amplifiers (this is similar to the procedure in homeopathy).

If you do not have any nanocoated stirrer you can use any stirrer, like a spoon or a rod or a blender.

This newly produced mixture (of pure distilled water and the few drops of GANS-water) Mr. Keshe usually calls “liquid plasma”. If you produce liquid plasma from GANS-water for internal use (to drink), you can put the GANS-water drops (or ml, tee spoon, soup spoon) also in normal drinking water. In this case you should not stir with a nanocoated stirrer, but only with a normal spoon.

Drying of the GANS

Optional: Drying the GANS with a fan

The aim of drying the GANS is the gentle withdrawing of water, the drying must not be carried out (under any circumstances) by heating upon open fire or on a stove. The more natural the drying happens the better it is. It is possible to speed up the drying process by putting it on top of a heating radiator or turning on a lamp (with a heat producing bulb) near the GANS container. If crystals are built during the drying process, the GANS was washed too little and these are salt crystals. Over time, you will receive GANS paste and after the lapse of another number of hours you will get GANS powder.

• CO2-GANS-Pulver.jpg

  CO2-GANS-Powder.

• 

  CuO-GANS-Powder.

• 

  CH3-GANS-Powder.

• 

  CuO-GANS-paste and CH3-GANS-Powder.

• 

  If the CH3 GANS is not enough washed salt crystals will form.

Application of plasma in emergency situations

Further information you can find at the 121. Knowledge Seekers Workshop, from Minute 21 and approx. Minute 35.

All health applications of the technology of the Keshe Foundation are researched only rudimentary. Much further investigation has to be done in this field of science. Clinical trials and tests are only possible after the respective permission is given. All recommendations and proposals given here or in the teachings of Mr. Keshe are the result of previous tests with volunteers or a deduction of the theoretical approach. Each application of these proposals given here or on other sites is carried out in personal responsibility and with the consciousness to be a volunteer making private tests with this Plasma-Technology in the area of health care.

As the previous tests have shown, plasma (the fields of which it consists) can help us in many situations very quickly. It can be applied by spraying, applying patches, drinking

To be prepared for emergency situations, the following GANS varieties should be promptly available, that are the GANS of:

• CuO (or CuO2) (copper-oxides, the first is a turquoise-blue, the second brownish)
• ZnO (or ZnO2) (zinc oxide, white)
• CO2 (carbon dioxide, whitish)
• CH3 (methyl group, reddish-brown)
• CaO 2 (Calcium Oxide, color?) (To produce from the ashes of burnt bones)

Of each kind of GANS at least 100 ml (milliliter) should be made. Add to each (already washed) GANS a few drops of the amino acids from the same container, in which the respective GANS was prepared, and stir well. Each kind of GANS (including the corresponding amino acids) should be filled in a normal, previously thoroughly washed, beverage bottle (for example, mineral water bottle). Fill up at a maximum to 1/3 of the bottle volume. Then fill fully with distilled water, shake well or stir and then leave it and let it settle (at least 24 h). Use only the GANS water above of the GANS flakes! The bottle can be repeatedly refilled. The GANS will therefore never be consumed (and retains its properties according to Mr. Keshe for more than three generations of men, perhaps many millennia). Even if during our lifetime no disasters happen, we can pass it as something valuable to our descendants. (How often you have to suck the GANS water and replace it with new distilled water, to prevent the formation of germs in it, the experience will show. Feedback to the Keshe Foundation is requested.)

• 

  GANS-water for spraying

• 

  GANS-water in the patch for placement on the body

• 

  GANS-water for drinking

GANS-Patches

GANS-water in bottles; please use on your bodies only the GANS-water above the GANS flakes.

In health applications the members of the Keshe Foundation use only the water above the GANS (the GANS-water) and/or the liquid plasma (see description above). The GANS itself must not be consumed under any circumstances. You must not touch GANS itself with any part of your body. For the so-called GANS patches or GANS pads mainly CO2-GANS-water or liquid plasma of CO2-is used. All work should always be performed with gloves!

This way GANS patches are created relatively quickly:

Method with GANS-water

1. Fill the clear water above the CO2-GANS (CO2-GANS-water) in a bottle. Add a few drops of CuO2-GANS-water into the bottle (and stir it well, the best with a nanocoated stirrer which you easily can produce by yourself with a nanocoated copper coil and a rod).
2. Prepare zip bags or a sealer and two layers of a kitchen roll (paper towel).
3. Drip 10-15 ml GANS-water of the prepared bottle onto the paper (according to the size of the patch take more or less of the liquid). Use a small syringe. If the whole paper is damp, put it into the bag, press out the air and close/seal the bag and label it immediately (what is the content, which GANS-waters used, in which ratio, date of production).
4. GANS-patches or pads should only be used by the people for whom they are made and intended. The best is to produce such patches consciously for a certain person with the intention that it should deliver exactly the fields which are needed for the healing process of this person. Do not transfer any GANS-patch to others after it was already used by someone. (Exception: emergency case).

Method with liquid plasma

1. Prepare liquid plasma (as described above) of the different types of GANS (separate or as a mixture in the ratio as recommended)
2. Prepare zip bags or a sealer and two layers of a kitchen roll (paper towel).
3. Drip 10-15 ml liquid plasma of the prepared bottle and one or two drops of CuO-GANS-water (pure) onto the paper (according to the size of the patch take more or less of the liquid). Use a small syringe. If the whole paper is damp, put it into the bag, press out the air and close/seal the bag and label it immediately (what is the content, which liquid plasmas in which ratio, how many drops of CuO-GANS-water are used, date of production).
4. GANS-patches or pads should only be used by the people for whom they are made and intended. The best is to produce such patches consciously for a certain person with the intention that it should deliver exactly the fields which are needed for the healing process of this person. Do not transfer any GANS-patch to others after it was already used by someone. (Exception: emergency case).

Test if you get better results when you use GANS-water for the patches or when you use liquid plasma for the production of the patches and please report the result of your research to the Keshe Foundation.

Dealing with the patches:

1. Simply apply them upon to aching area.
2. Works well on a bandage or plaster too. Hand, arm shoulder, hip, knee, foot, ribs, solar plexus, neck etc.
3. In restlessness, grief, fears, worries: on solar plexus and neck ...

Caution: Do not use such patches on body parts which contain artificial material, for example nails, screws, plates, after surgical interventions. Do not apply at teeth with root canal treatment. Not on or near pacemakers

Mobile Plasma Units

Mobile Health Unit, created with a vacuum sealer.

A Plasma Unit consists basically of two "walls" on which either coils or GANS-patches are mounted. The human stands between these walls. Through his body, the plasma flows from the rear to the front. The closer the coil or patches to the body, the better the body fields can be supplied.

While the Health Unit with coils*** is very complex and complicatedly to build, this mobile unit is very easy to create, especially if it is necessary to have it quickly. You only have to attach multiple GANS- patches on the front and back of the body. It is only important that a flow of the plasma (field flow) takes place from the rear to the front. For the fields to flow in the right direction from the back towards the front of the body the patches in the back part have to provide stronger fields than the patches in the front part.

(***For stationary health units please consider the respective blueprints (LINK) )

Typically the right direction of field flow can be achieved by adding CO2-/ zinc oxide GANS-water in the patches of both sides and one or more GANS-waters additionally in the patches on the back. This can e.g. be CH3-GANS-water, some CuO-GANS-water and / or Food-GANS-water. Another possibility would be, to attach all patches into one piece of sealed foil (with the front and rear part, including a hole for the head). You can create this e.g. with a vacuum sealer, as can be seen in the photo.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Decontamination of Water

Ratio of CuO-water to contaminated water

In order to ensure that people will have clean drinking water for their demand, the CuO- GANS-water or CuO”-GANS-water is used for decontamination of water. The dilution is 1:100. So use 1 liter CuO- or CuO2-GANS-water to 100 liters of contaminated water. Pour the CuO- or CuO2-GANS-water into the container with the contaminated water, stir and allow it to settle for 12 h. Then extract from above the clean water. From 100 liters polluted water so at least 50 liters of clean water can be produced.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Internal and external injuries

CO2- and ZnO-GANS-water acts excellently as a spray, if sprayed on painful areas, (be careful: do not apply directly upon fractures, only around them, the bone needs the pain for the calcium to be created/incorporated). You can spray it also on clothes, tents and so on to protect against nuclear radiation and to keep warm.

In all situations of crisis our mind is so heavily loaded with all fears, confusion, depression, exuberant emotions and so on. In this cases always spray CO2- and ZnO-GANS-water (mixture) or drink it drop-wise (diluted in a glass or bottle of water) and / or apply patches on the solar plexus and neck. Also the compound of CO2-, ZnO- and CH3-GANS-water can be used to strengthen the nervous system. Namely in a ratio of 20% CH3-, 10% ZnO- and 70% CO2-GANS-water with a little amount of amino acids (only one drop of each kind).

In cases of exhaustion and/or hunger, combine CO2-/ ZnO2- with CH3-GANS-water. If you have it, apply two patches of different strength, one upon the solar plexus and the stronger one on the back, for example: CO2-/ ZnO2- and Food-GANS-water with amino acids at the back and CO2-GANS-water at the solar plexus.

With open injuries, two or three different patches can be used: CO2-, CH3- and CuO2-GANS-water. Make three different patches and place them one above the other. They can be placed directly over the dressing. The CuO2-patch is to apply only for a short time. Its purpose is to prevent infection of wounds.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Infections of the skin, external injuries of the skin, cuts, sunburn, insect bites etc.

(See 121. Knowledge Seekers Workshop, approximately from 29 minutes)

Application of liquid plasma created with drops of GANS-water:

CuO + Co2 (in the ratio 50%/50%) for spraying or patches 

Pour the liquid plasma (water with the same amount of drops of CuO- and CO2-GANS-water) into a spray-bottle and spray the wounds directly, or a dump a paper napkin / paper towel with this mixture and apply it on the body part.

When you have an insect bite, wash it with CO2-GANS-water to which you added only 1 drop of CuO-GANS-water.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Deep wounds with internal injuries (of inner organs) (except head; all which is below the neck)

(See 121. Knowledge Seekers Workshop, approximately from 29:50 minutes) Application of liquid plasma created with drops of GANS-water:

CuO2 (5 drops) + CO2- (3 drops) + ZnO (1 drop) + COHN (amino acids – 1 drop of each kind of GANS) oral, drink the drops diluted in a glass or bottle of water

1. CuO or CuO2 repairs muscle tissue and accelerates healing
2. CO2 connects, provides communication for the tissue repair, gives the body a part of the necessary energy
3. ZnO stabilizes emotions
4. COHN (Amino acids) provide the connection to the body

This mixture accelerates the healing of the injured tissue.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Fractures

(See 121. Knowledge Seekers Workshop, approximately from 32 minutes) Application of liquid plasma created with drops of GANS-water:

CO2 (2 drops) + Cu0 (3-4 drops) + CH3 (1 drop) + COHN (1 drop) + CaO Calcium oxide (1-2 drops) put a soaked towel around the fracture (not directly on the point of fracture).  

1. CO2-gives the body the necessary energy and provides the communication within the body
2. CuO and CuO2 disinfects and helps in muscle tissue healing
3. CH3 (iron GANS-water) amplifies energy for the healing process
4. COHN (amino acids) provide the connection to the body
5. CaO (Calcium oxide) for the reconstruction of bones

CaO-GANS can be produced easily from the ashes of burnt bones.

Do not apply the soaked towel or spray directly upon the point of fracture, but only around the area of the fracture.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Head injury / brain injury

(See 121. Knowledge Seekers Workshop, approximately from 34 minutes) Application of liquid plasma created with drops of GANS-water:

CO2 (3 drops) + CaO (3 drops) + ZnO (4 drops) apply with patches or tubes

Begin with this application only after 2-3 weeks, as the brain itself starts to regenerate!!! Calcium oxide (CaO2) is needed for brain cells, usually the brain cells take calcium from the bones of the skull.

COHN (the amino acids) are important for the connection between the fields of the liquid plasma and the area of injury. They support the repair work of the body.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Disinfecting effect

(See 119th Knowledge Seekers Workshop, about 2 hours 21 minutes)

CuO-GANS-water mixed with CO2-GANS-water could serve as a disinfectant for surgical instruments and hands. It has however still to be explored. Feedback from physicians is appreciated.

CO2-GANS-water with very little CuO-GANS-water (see 119th Knowledge Seekers Workshop, about 2 hours 25 minutes) can be given in a spray bottle and used as a disinfectant solution (in toilets, kitchens, unpleasant odors disappear, usable as deodorant...). You can spray this solution on the skin, at skin diseases, even skin cancer, burns, ... With foot infections spray it, spray corns and apply patches too. If bald or with thinning hair spray on the scalp and massage.

There is little experience, it just has to be tested. Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Treatment of eye problems

(See 22 International Knowledge Seekers Workshop, about 1 hour 40 minutes)

In degenerative eye diseases, by the application in some cases the genetic cause can be changed, or if they are emotionally conditioned, the emotional balance can be restored, so that as a result the eyes are able to recover again.

Degenerative eye diseases can be processed with 3 GANS types:

1. the GANS water of CO2 is used to connect the physicality with emotions = communication (4-5 drops)
2. the GANS water of ZnO is used to provide support for the emotions (1-2 drops)
3. The GANS water of CH3 is used to provide the energy for the recovery of the cells (for the conversion of the fields into matter) (2 or 1 drop)

(Caution! With eye cancer you MUST NOT use CH3-GANS-water because this promotes the growth!)

But for the treatment of muscles which move the eyeball for focusing, one needs in addition

1. CuO2-GANS-water (1/2 to 1 drop, 1 drop will already be too much), which supports the regeneration of muscle tissue

In the mixture you add very little (1 drop) of the amino acid from CO2-GANS.

But you should not use amino acids of CuO2-GANS, except when a muscular weakness of the eye muscles is present. Then you can add the amino acids of CuO2 GANS (but very little).

Whenever nerves are affected, add also the amino acids of ZnO-GANS to the mixture.

To consider in the health sector, which GANS types should be used, one must consider the causes of the disease and the affected tissue. The amino acids always provide the link between the fields provided by the GANS-water to the respective physical area in the body (CO2 generally, ZnO nerves, CuO2 muscle tissue, CaO bone tissue). Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Application of GANS water in relation to viruses

(See 135. Knowledge Seekers Workshop, approximately from 30 minutes)

This technology is suitable for dealing with viruses.

Viruses dock to their respective host cells. The CO2-GANS-water is capable to separate this connection (by interaction of the fields of the CO2-GANS-water with then fields of the virus, and by creating a field balance, so that no further fields are available for the connection with the host cell).

Everything you need is therefore the CO2-GANS-water. At the moment when one perceives an infection, and the physician has determined that it is a viral infection, you can take 2-3 teaspoons CO2-GANS-water and then continue taking the same dose for 2 to 5 days. The virus should disappear, even if he is still there, he will no longer be effective.

In rare, very serious cases you can add in a ratio of 1:10 also CuO-GANS-water, that is:

9 units (drops) CO2-GANS-water + 1 unit (drop) CuO-GANS-water

Feedback and report of experiences to the Keshe Foundation are requested.

Is someone getting a flu shot, so CO2-GANS-water can be taken additionally.

Flu

If a flu starts with high fever, so you should take within the first half hour 3-4 tsp (teaspoon) CO2-GANS-water with a drop of CuO-GANS-water, every 5 minutes. The temperature would have to drop quickly. Then do the same 2-3 times in the next hour and still 3-4 times during the rest of the day, then 3 - 4 times daily 2-3 tsp for 2 - 3 days. The hands should be washed with CO2-GANS-water too.

The pathogenic fields are literally washed out of the body through the CO2-GANS-water. This GANS water supports an internal cleansing process.

If you have children with a high fever, you can wash or rub the body with the CO2-GANS-water. Possibly also add a drop of CuO2-GANS-water. The temperature will fall quickly.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Ebola, Malaria

Take 3 - 5 teaspoons or tablespoons CO2-GANS-water per day for 30 to 60 days, possibly even 100 days

Use at your own risk and danger. Feedback and report of experiences to the Keshe Foundation are requested.

Aids (HIV-positive)

(Procedure of Paul from Togo: see 135. Knowledge Seekers Workshop, approximately from 1 hour 48 minutes) 1. For 15-30 days only the liquid plasma of CO2-GANS-water should be used for drinking, cooking, bathing, housecleaning, laundry cleaning, hand washing, etc. You should not drink anything else. (An indication from Paul regarding the amount of CO2-GANS-water which is added to the drinking water was missing; Mr. Keshe recommended 3-4 times a day 1 tablespoon CO2-GANS-water with a few drops CuO-GANS-water to add to the drinking water). 2. Thereafter you should produce Liquid plasma from a mixture of CuO-GANS-water CH3 GANS water CO2-GANS-water and ZnO-GANS-water (in equal parts), and only this liquid plasma should be used for drinking, cooking, bathing, housecleaning, laundry cleaning, hand washing, etc. You should not drink anything else.

The first phase is used to purify the body. After several days this can lead to fatigue, nausea, blood in the urine or pain etc. In this time the body needs all the energy for healing, so you should sleep a lot. This condition should have disappeared after about 2 weeks. Then one can go from the first to the second phase.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Bacterial diseases

Bacteria are easier to treat. If the doctor prescribes an antibiotic, one can (in an autonomous, self responsible test) reduce the amount of the antibiotic (for example halve the tablet or cut in even smaller pieces) and additionally take in CO2-GANS-water. It should prevent the arise of resistance to the antibiotic and cause the antibiotic to have a better effect. Feedback and advice to the Keshe Foundation are requested.

Use at your own risk and danger. Feedback and report of experience to the Keshe Foundation are requested.

Use in the oral hygiene

(See 135. Knowledge Seekers Workshop, approximately from 56 minutes)

Instead of using toothpaste mouth can be flushed with CO2-GANS-water. It should be ensured that the liquid wets all areas of the oral cavity and the palate. This leads to a balancing of the environment in the mouth. This in turn prevents tooth and gum disease (because the microorganisms cannot find the right environment for propagation). This procedure is intended to prevent. Existing dental defects can thus not be repaired, but the progression should be broken. Some of the liquid can be swallowed, so it must not be regurgitated.

In addition one can chew 2-3 times a week at bedtime, a small piece of cheese and swallow it. This should also have a positive effect on the oral environment and help to prevent dental disease.

If precipitated milk teeth have been collected (is common in some countries) so they can be used for the production of Calcium-GANS which then supplies exactly the calcium-fields that are suitable for this man or woman.

For GANS production you can dissolve the teeth in lemon juice (or Coca Cola) and only afterwards you add the NaOH (method as in the Food GANS production).

As an alternative to physical GANS production from the teeth you can transmit the information of the teeth on water. For this purpose you take a round container with water and put 5 little bottles (vials) around it (evenly distributed), one with CO2-GANS, one with CH3-GANS, one with ZnO-GANS, one with CuO-GANS and the last one with the amino acids from the CO2-GANS production. Now lie or hang the tooth (teeth) directly above of the water. Over time, the water absorbs the fields from the bottles and from the tooth. This water you can drink. Or, if you e.g. intend to use it for the support of the healing of a bone fracture, apply a patch on the body, namely in front and back (or left and right) of the part of your body near the point of fracture.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Use in functional failure of organs

(See 135. Knowledge Seekers Workshop, approximately from 2 hours 23 minutes) The method of information of water by the 5 GANS-bottles attached around a container with water, as described above, can also be used when someone is to be supported in the healing of an organ with functional loss.

In the future probably no more organ transplants will be necessary. So you could, for example, if somebody has bone marrow problems, find a healthy family member, who sits or lies with the upper part of the knee (where the kneecap) above the water container (with the 5 vials around). The information about the fields of the healthy bone marrow goes into the water beneath. Then the patient with the bone marrow problems can drink this water. In the future, Mr Keshe will add more information to this topic.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.

Toxins from the body wash

(See 135. Knowledge Seekers Workshop, approx. 1 hour 13 minutes and from 2 hours 32 minutes) It should also be possible to wash toxins out of the body by using GANS-water. It would be interesting to see if this will work for snake venom by snake bite or the like. You could rinse the bite wound with a mixture of CuO- and ZnO-GANS-water and then drop a mixture of CO2-GANS-water and ZnO-GANS-water (50:50) into the bite wound or drink it.

Cortisone retention after high doses of cortisone can get out of the body with CO2-GANS-water and the essential oils of citrus fruits, but this is a prolonged process. Collect the oils from the peel of citrus fruits and mix it into the CO2-GANS-water. Then wash your hands or wash the affected parts of the body with it.

Application only at your own risk and responsibility. Please report your experiences to the Keshe Foundation.